Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 3655 — Trang 11/16

Code: 71-215-00

Description: Tray 1 Feeder Composition Error 71-215-00 Tray 1 Feeder Composition Error NOTE: Status codes 03-561 and 72-215 are raised with this fault code.
Remedy: Verify product and option compatibility, The Tray is supported. Y↓N→Install the correct Tray. Perform GP 9 to reload system software. Reinstall the Tray and test. The error persists. Y↓N→Perform SCP 6 Final Actions. Perform a Forced AltBoot GP 9 to reload system software.

Code: 72-098-00 ... 74-098-00

Description: Option Feeder Mode 72-098-00 Option Feeder2 Mode 73-098-00 Option Feeder3 Mode 74-098-00 Option Feeder4 Mode NOTE: Status codes 03-561 and 77-098 are raised with this fault code.
Remedy: Cycle system power. The error persists. Y↓N→Go to SCP 6 and complete the Final Actions. Remove the Optional Feeder, then obtain the appropriate system software set and perform GP 9 to reload system software. Reinstall the Optional Feeder and test. The error persists. Y↓N→Perform SCP 6 Final Actions. Replace the Feeder Board .

Code: 72-101-00

Description: Tray 2 Misfeed Jam 72-101-00 Tray2 Misfeed Jam NOTE: Status code 07-502 is raised with this fault code.
Remedy: Check the Nudger, Feed, and Retard Rollers for excessive wear or contamination. The rollers are undamaged and clean. Y↓N→Clean or replace the rollers. Use dC330 code 071-119 to test the Tray 2 Path Sensor. The sensor signal changes. Y↓N→Replace the Path Sensor . Use dC330 code 071-018 to test the Tray 2 Feed Solenoid. The clutch activates. Y↓N→Replace the Feed Clutch . Use dC330 code 071-021 to test the Tray 2 Registration. The clutch activates. Y↓N→Replace the Registration Clutch . Use dC330 code 071-009 to test the Tray 2 Feed Motor. The motor rotates. Y↓N→Replace the Feed Motor . lnstall new components as necessary: • Option Feeder Feed Assembly • MCU Board

Code: 72-102-00

Description: Feeder Path 2 Sensor On Jam (RC2) 72-102-00 Feeder Path 2 Sensor On Jam (RC2) NOTE: Status code 07-508 is raised with this fault code.
Remedy: Check the Nudger, Feed, and Separator Rollers for excessive wear or contamination. The rollers are undamaged and clean. Y↓N→Clean or replace the rollers. Use dC330 code 071-102 to test the Registration Sensor. The sensor signal changes. Y↓N→Check the connection between the HVPS and MCU Board. The connection is secure. Y↓N→Secure the connection. Replace the HVPS . Use dC330 code 071-119 to test the Tray 2 Path Sensor. The sensor signal changes. Y↓N→Replace the Path Sensor . Use dC330 code 071-018 to test the Tray 2 Feed Solenoid. The clutch activates. Y↓N→Replace the Feed Clutch . Use dC330 code 071-021 to test the Tray 2 Registration. The clutch activates. Y↓N→Replace the Registration Clutch . Use dC330 code 071-009 to test the Tray 2 Feed Motor. The motor rotates. Y↓N→Replace the Feed Motor . lnstall new components as necessary: • Option Feeder Feed Assembly • MCU Board

Code: 72-215-00

Description: Tray 2 Feeder Composition Error 72-215-00 Tray 2 Feeder Composition Error
Remedy: Cycle system power. The error persists. Y↓N→Perform SCP 6 Final Actions. lnstall new components as necessary: • Option Feeder Board • Optional Feeder Assembly • MCU Board

Code: 72-216-00

Description: Option Feeder Motor2 Error 72-216-00 Option Feeder Motor2
Remedy: Use dC330 code 071-009 to test the Tray 2 Feed Motor. The motor rotates. Y↓N→Replace the Feed Motor lnstall new components as necessary: • Option Feeder Board • MCU Board

Code: 73-101-00

Description: Tray3 Misfeed Jam 73-101-00 Tray3 Misfeed Jam
Remedy: Check the Nudger, Feed, and Retard Rollers for excessive wear or contamination. The rollers are undamaged and clean. Y↓N→Clean or replace the rollers. Use dC330 code 071-120 to test the Tray 3 Path Sensor. The sensor signal changes. Y↓N→Replace the Path Sensor . Use dC330 code 071-019 to test the Tray 3 Feed Solenoid. The clutch activates. Y↓N→Replace the Feed Clutch . Use dC330 code 071-022 to test the Tray 3 Registration. The clutch activates. Y↓N→Replace the Registration Clutch . Use dC330 code 071-009 to test the Tray 2 Feed Motor. The motor rotates. Y↓N→Replace the Feed Motor . lnstall new components as necessary: • Option Feeder Feed Assembly • MCU Board

Code: 73-102-00

Description: Path 3 Sensor On Jam (RC3)
Remedy: Check the Nudger, Feed, and Separator Rollers for excessive wear or contamination. The rollers are undamaged and clean. Y↓N→Clean or replace the rollers. Use dC330 code 071-102 to test the Registration Sensor. The sensor signal changes. Y↓N→Check the connection between the HVPS and MCU Board. The connection is secure. Y↓N→Secure the connection. Replace the HVPS . Use dC330 code 071-120 to test the Tray 3 Path Sensor. The sensor signal changes. Y↓N→Replace the Path Sensor . Use dC330 code 071-019 to test the Tray 3 Feed Solenoid. The clutch activates. Y↓N→Replace the Feed Clutch . Use dC330 code 071-022 to test the Tray 2 Registration. The clutch activates. Y↓N→Replace the Registration Clutch . Use dC330 code 071-012 to test the Tray 3 Feed Motor. The motor rotates. Y↓N→Replace the Feed Motor . lnstall new components as necessary: • Option Feeder Feed Assembly • MCU Board
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie