• Code: 32:01.1
• Description: This system error occurrs when there is a small amount of paper printed (less than 79 inches (200cm) long.
• Remedy: • Check there is no obstacle between the Take-up reel optical sensors. • Check the paper is attached to the TUR spindle. • Check the TUR switch is in the correct position. • If needed, use the TUR arrow keys to wind paper before resume printing. • To resume printing, press OK.

• Code: 32:01.2
• Description: This system error happens when there is a small amount of paper printed (less than 70 inches long), and the Take Up Reel sensor detects that the loop shaper is (incorrectly) at the bottom of its path, even though the spindle motor has been rotating for more that 3 seconds. The most probable cause of this error is the user has forgotten to set the switch direction or tape the paper to the spindle core, when the paper reaches the floor and blocks the TUR IR sensors.
• Remedy: • Check that there is no interference around the Take-up-reel optical sensors. • Check the paper is attached to the TUR spindle. • Check the TUR switch is in the correct position. • Check there is no obstacle between the Take-Up Reel optical sensors • If required, use the TUR arrow keys to wind paper before resuming the print. • When the jam is cleared, printing is resumed. Press the Ok key to clear the Warning message.

• Code: 32:02
• Description: This message is shown during initilization of the printer and is meant as a warning that the TUR has been disconnected while the printer was off. This error is also shown if the user tries to enable the TUR but it is not connected to the Printer.
• Remedy: Connect the Take-up Reel to the Printer and press Ok to continue.

• Code: 41:03
• Description: Electrical current limit in paper motor.
• Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Replace the Media-Axis Motor . • If the System Error continues, replace the PrintMech PCA .

• Code: 41:10
• Description: Electrical fault in paper motor.
• Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Media-Axis Motor cable is not damaged and is correctly connected to the PrintMech PCA. • Replace the Media-Axis Motor . • If the System Error continues, replace the PrintMech PCA 

• Code: 42:03
• Description: Electrical current limit in carriage motor.
• Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Open the Window and check for any visible obstacles restricting the movement of the Carriage Assembly. If there is a wrinkled mass of media blocking the Carriage Assembly, then clear the obstruction. • Clean the Encoder Strip . • Replace the Scan-Axis Motor . • If the System Error continues, replace the PrintMech PCA .

• Code: 42:10
• Description: Electrical fault in Carriage Motor or starting the Scan Axis or Homing Scan Axis.
• Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Scan-Axis Motor cable is not damaged and is correctly connected to the PrintMech PCA. • Clean the Encoder Strip using a lint free cloth dampened with tap water, then reset the counter (Setup > Resets > Encoder cleaning) Ë See the instructions provided in the User Maintenance Kit and  • Replace the Scan-Axis Motor . • If the System Error continues, replace the PrintMech PCA 

• Code: 43:10
• Description: Vacuum Fan Sstopped.
• Remedy: • Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Vacuum Fan cbles are not damaged and are correctly connected to the Interconnect PCA. • Also check that the cables between the Interconnect PCA and the PrintMech PCA are not damaged and are correctly connected. • Replace the Interconnect PCA . • Replace the Vacuum Fan . • If the System Error continues, replace the PrintMech PCA 